
Indexat a
Llicència i ús
Grant support
This investigation was supported by Comunidad de Madrid (S-S2009/MAT-1585), EFDA-ITER (WP12-MAT-W ALLOY), Ministerio de Economia y Competitividad of Spain (ENE2012-39787-C06-05 and MAT2012-38541-c02-02). TEM measurements have been made at LABMET, TEM Laboratory associated to the Red de Laboratorios de la Comunidad de Madrid.
Anàlisi d'autories institucional
Palacios, T.Autor (correspondència)Pastor, J. Y.Autor o coautorAguirre, M. V.Autor o coautorMartin, A.Autor o coautorMechanical behavior of tungsten-vanadium-lanthana alloys as function of temperature
Publicat a:Journal Of Nuclear Materials. 442 (1-3): S277-S281 - 2013-11-01 442(1-3), DOI: 10.1016/j.jnucmat.2013.02.006
Autors: Palacios, T; Pastor, J Y; Aguirre, M V; Martin, A; Monge, M A; Munoz, A; Pareja, R
Afiliacions
Resum
The mechanical behavior of three tungsten (W) alloys with vanadium (V) and lanthana (La2O3) additions (W-4% V, W-1% La2O3, W-4% V-1% La2O3) processed by hot isostatic pressing (HIP) have been compared with pure-W to analyze the influence of the dopants. Mechanical characterization was performed by three point bending (TPB) tests in an oxidizing air atmosphere and temperature range between 77 (immersion tests in liquid nitrogen) and 1273 K, through which the fracture toughness, flexural strength, and yield strength as function of temperature were obtained. Results show that the V and La2O3 additions improve the mechanical properties and oxidation behavior, respectively. Furthermore, a synergistic effect of both dopants results in an extraordinary increase of the flexure strength, fracture toughness and resistance to oxidation compared to pure-W, especially at higher temperatures. In addition, a new experimental method was developed to obtain a very small notch tip radius (around 5-7 mu m) and much more similar to a crack through the use of a new machined notch. The fracture toughness results were lower than those obtained with traditional machining of the notch, which can be explained with electron microscopy, observations of deformation in the rear part of the notch tip. Finally, scanning electron microscopy (SEM) examination of the microstructure and fracture surfaces was used to determine and analyze the relationship between the macroscopic mechanical properties and the micromechanisms of failure involved, depending on the temperature and the dispersion of the alloy. (C) 2013 Elsevier B.V. All rights reserved.
Paraules clau
Indicis de qualitat
Impacte bibliomètric. Anàlisi de la contribució i canal de difusió
El treball ha estat publicat a la revista Journal Of Nuclear Materials a causa de la seva progressió i el bon impacte que ha aconseguit en els últims anys, segons l'agència WoS (JCR), s'ha convertit en una referència en el seu camp. A l'any de publicació del treball, 2013, es trobava a la posició 2/33, aconseguint així situar-se com a revista Q1 (Primer Cuartil), en la categoria Nuclear Science & Technology.
Des d'una perspectiva relativa, i atenent a l'indicador de impacte normalitzat calculat a partir de les Citacions Mundials de Scopus Elsevier, proporciona un valor per a la mitjana Ponderada de l'Impacte Normalitzat de l'agència Scopus: 1.03, el que indica que, comparat amb treballs en la mateixa disciplina i en el mateix any de publicació, el situa com un treball citat per sobre de la mitjana. (font consultada: ESI 14 Nov 2024)
Aquesta informació es reforça amb altres indicadors del mateix tipus, que encara que dinàmics en el temps i dependents del conjunt de citacions mitjanes mundials en el moment del seu càlcul, coincideixen a posicionar en algun moment el treball, entre el 50% més citats dins de la seva temàtica:
- Field Citation Ratio (FCR) de la font Dimensions: 3.08 (font consultada: Dimensions Jul 2025)
Concretament, i atenent a les diferents agències d'indexació, aquest treball ha acumulat, fins a la data 2025-07-26, el següent nombre de cites:
- WoS: 25
- Scopus: 29
- Open Alex: 28
Impacte i visibilitat social
Anàlisi del lideratge dels autors institucionals
Hi ha un lideratge significatiu, ja que alguns dels autors pertanyents a la institució apareixen com a primer o últim signant, es pot apreciar en el detall: Primer Autor (PALACIOS GARCIA, TERESA) .
l'autor responsable d'establir les tasques de correspondència ha estat PALACIOS GARCIA, TERESA.